17 janvier 2006

Fridge & Freezer Survival Guide

Lots of people do daft things with fridges and freezers as well as fridge freezers in this article I’ll try to walk you through the major do’s and don’ts from installation to disposal.

Installing A Fridge freezer, Fridge Or Freezer

Do

Make sure that you have adequate ventilation especially on built in or integrated fridges, freezers and fridge freezers. Not having proper ventilation will almost certainly result in an overheating compressor and a very large repair bill.

Study the installation instructions carefully and follow them. If your installer is doing it for you, make sure they read these!If your fridge is one of the US style ones and need water make sure that the water supply is clean. Peaty water or dirty water can clog inlet valves.Don’t

Install next to a heat source such as an oven or a radiator. This can produce more heat and has the same effect as inadequate ventilation and cause the early demise of the unit.

Installing next to an oven or cooker can mean that leaking heat from the oven will warp the door seals and cause a “not sealing” fault. This means the unit will run longer and you can get a possible ice build up inside.

Install in a room that is too cold or too warm, refrigeration doesn’t like that.Keeping It As Energy Efficient As PossibleDo

Try to keep the door shut as much as you possibly can. When you open the door up to 30% of the cold air is lost meaning that the fridge or freezer has to work extra to get the temperature back down again, the more work, the more wear and tear and, therefore, the more chance of failure.

On older fridges make sure that the door seals are sealing correctly. If they’re not then a good tip is to heat with a

hair dryer and often the seals will spring back into position.

Make sure that the drain hole at the back of wet wall fridges is clear or you will get water in the fridge. See our basic fault guide for more on this.

Don’t

Leave the fridge or freezer door open!

Pack a whole heap of fresh unfrozen food in the freezer in one go. This will cause a significant temperature rise meaning the unit has to work really hard to get the temperature back down and your food frozen. Put in a bit at a time to allow the unit to settle efficiently.

Leave fast freeze on as this overrides the thermostat and makes the freezer run constantly.

Cleaning

Don’t

Use any sharp metal implement anywhere near a fridge or freezer! You risk serious and very possibly irreparable damage if you puncture something, including the inner walls.

Use carcinogenic cleaners. Simple bleach or anti-bacterial spray only or you could damage or weaken interior plastic parts of the refrigerator.

Do

Keep it clean! This especially applies to the door seals as spillage gets in behind them and will smell.

Defrosting

Do

Use plastic scrapers or allow to defrost naturally with the doors open and the power off.

Don’t

Use metal implements as above

Use heat guns or anything else that if water drips onto is liable to electrocute you!

Disposal

Do

It properly, call the local council and if you have to pay, you have to pay! Refrigeration needs disposed of safely and properly so do the right thing.

Don’t

Fly-tip a fridge! It’s illegal, immoral and potentially lethal.

Every year we hear reports of kids playing in old dumped fridges and freezers and there has been a few fatalities and several injuries, some serious, from kids getting stuck in one. They don’t know any better, you do.


1 janvier 2006

Entretenir son réfrigérateur

Nettoyage intérieur
Enlevez tous les composants (plateaux, bac à légumes, éléments de la porte) et lavez-les à l’eau tiède additionnée de détergent doux, type liquide vaisselle, avec une éponge. Passez-les ensuite dans de l’eau légèrement javellisée pour les désinfecter et éviter la prolifération des microbes. Rincez et séchez. Lavez de la même manière les parois internes, en ajoutant un peu de jus de citron à l’eau pour éliminer les mauvaises odeurs. Astuce : placez en permanence un demi-citron à l’intérieur de votre réfrigérateur pour réduire les odeurs désagréables.

Nettoyage extérieur
Lavez à l’aide d’un chiffon doux ou d’une éponge humectée d’eau savonneuse, mais n’utilisez jamais de produits abrasifs et d’ustensiles qui pourraient rayer l’appareil.

Le dégivrage du congélateur
Sur les appareils à froid ventilé (voir critères), plus de corvée de dégivrage. Le froid est sec car débarrassé de son humidité donc le givre ne se dépose plus sur les parois. Certains appareils sont équipés du système de dégivrage automatique ou semi-automatique. Dans le premier cas, le réfrigérateur élimine l’eau régulièrement sans que l’on s’en préoccupe. Dans le deuxième cas, après avoir déclenché le processus de dégivrage en réglant le thermostat, il ne reste plus qu’à récupérer l’eau. Si aucun de ces systèmes n’est présent sur votre appareil, il faut procéder au dégivrage manuel avant que la couche de givre n’atteigne 3 cm. Réunissez les denrées dans des sacs isothermes, débranchez le réfrigérateur, et pour accélérer la fonte de la glace, placez dans le compartiment un récipient rempli d’eau bouillante, tout en laissant la porte ouverte. Grattez ensuite les parois à l’aide d’un ustensile non tranchant (raclette en plastique) pour ne pas les endommager. Récupérez l’eau, épongez et séchez un maximum le congélateur puis rebranchez l’appareil.

Joints d’étanchéité
Ils sont indispensables pour garder le réfrigérateur à température idéale. Il faut donc les remplacer dès que leur état se détériore. Astuce pour tester leur efficacité : fermez la porte sur une feuille de papier. Si vous pouvez l’enlever sans ouvrir, les joints sont à changer.

Serpentins
Situés à l’arrière du réfrigérateur, ces échangeurs thermiques doivent être dépoussiérés et nettoyés afin de garantir un meilleur rendement au réfrigérateur. Vous pouvez utiliser un petit aspirateur, une brosse ou un chiffon. Cette opération peut se révéler dangereuse si les serpentins possèdent des bouts pointus, restez attentif et consultez éventuellement la notice de votre appareil.

Close
E-mail It